Search results

You're right, I missed that part. I do not have that enabled which is why it was working for me. Sorry Madcodger, I'll stop trying to help :rolleyes:

I was just able to log into my Elk M1XEP using my Mac Mini. I poked around and was able to control lighting, read status, etc. Do you have your Elk M1XEP set up using the secured or non-secured port? Regards, Ultrajones

You mentioned on the HomeSeer message board that you are experiencing packet loss when pinging the Elk M1XEP. Have you tried replacing the cable that connects your Elk M1EXP to your switch? I have seen simliar issues in the past and it turned out to be an incorreclty wired cable. Regards...

Thank you for the replies. I also sent an email to Brultech. I received a reply within an hour! I download the Brultech's EtherBee Configurator and the unit is up and running. I can *finally* start writing software for the ECM-1240 :-) Regards, Ultrajones

I just purchased the Brultech serial to ethernet adapter. It came with no instructions whatsoever. Does anyone have the instructions on how to hook it up to the ECM-1240? Regards, Ultrajones

I extended the CT's about 25 feet using 2 cat 5 cables. 1 cat 5 cable (2 pair) is used for the main CT's and the other cat 5 cable (4 pair) is used for AUX input 1-4. Seems to work great after I fixed the wiring issue ;)

Found the issue! The white and black wires coming from the split-100 CT's are not bundled together, so I ended up wiring them up incorrectly (white wire from one, black wire from the other). I corrected the wiring issue and all manual load tests now pass (including the AUX inputs). Thank you...

And here is a shot of the ECM-1240 ...

I recently installed a Brultech ECM-1240. While testing the basic installation, I could see an increase of 100 watts on CH 1 when I turned on a lamp connected to the first phase. However, when turning on a lamp on other phase, I don't see an increase or decrease in watts registered on CH 1...

Paul, How can I tell if my panel is fed from a 3-phase system? I have one main panel and one 50 amp dedicated to my AC that the power company can cut out during periods of high load. Regards, Ultrajones

Hello Will. No, I only have one CT installed on each AUX channel. However, at this point, I only have AUX 1 connected until I sort out this issue.

Hello Paul. Thanks for helping. No, that doesn't seem to have helped the issue. I have the SPLIT-100 CT's connected as described on the top of page 13 in the manual. I have the config for CH 1 set to SPLIT-100, dual CT. Regards, Ultrajones

I just finished hooking up my ECM-1240. I have CH 1 connected to my main panel and AUX 1 - 4 connected to various 120 volt breakers. Shouldn't the total watts for AUX 1-4 be less than the watts listed for ch1? See picture. Regards, Ultrajones

Is this the thread you are looking for? http://www.cocoontech.com/forums/index.php?showtopic=9232

I didn't think it would be this hard to connect an Elk siren to the Elk M1G. I will check with Elk to see what they say. Thanks for the replies. Regards, Ultrajones

Do I win something for having a *really* challenging question? :)

Hello All. Can I hook an ELK-SS30 siren directly to output 2 on my Elk M1 Gold? The specs show the ELK-SS30 siren draws 1.1 amps at 13.8vdc, but the Ek M1 ouput 2 is limited to 1 amp. If I can connect it, how is it wired? There are 3 wires on the siren, but only 2 connection for output 2. Do...

I also sometimes experience this issue when disarming my system using a KP1. While entering the disarm code, the kepyad flashes and appears to reset. I am able to disarm the system once it comes back to life. I don't ever recall feeling a shock or static discharge though. I also have arrived...

I use the Elk M1 / HomeSeer / Insteon / HAI Thermostat to conserve energy in my home. Lights are automatically turned off when a room has been vacant for 30 minutes and my thermostat is automatically set back when my alarm is armed "away". I also use home automation to disable my sprinkler...

I am running 1.0.0.22.