Search results

Not correct : it accepts up to 6 ds1820 temp sensors or their 1-wire based humidity sensor I read all the manual :-) They don't support (yet) HB sensors but I have asked them feedback about their roadmap I will keep you in the loop

Hello I find this device x320m : http://www.controlbyweb.com/x320m/ Very very promising device for weather stations and dashboarding I Presume this is compatible with HB thermo and humidity sensors Any experience with this ? thomas

Soon the same for iOS ? If you need beta tester I can send you my udid

Tx However I measure a correct 3v on the pcb below the battery Strange !

Hello Maybe for Revision 2.0, but here are some ideas for your expansion board: -Add opto-coupler for all 8 logical inputs -Add small SSR as output protection: PVT312 -one ground 0V connection point is maybe too few for 8 inputs ? Thank you

Any idea where I can find such cell with small connected pins ?

The cell is soldered via 2 small pins on the pcb as stated in the manual Strange they are flat. As I did solder myself need to check if this is well done first ... Thank you

Hello I bought some dual counters in 2010. seems now that each time I disconnect from the 1w network, their counters are reset to 0. Battery expired ? How can I be sure ? Easily replacable ? Seems I need to solder. Hope not double face.... why not using a small battery plug to facilitate...

Hello I was wondering if this 6 channels hub has ESD protection ? Or should I interconnect between the hub and each sensors leg some ESD protection ? Can you recommend some schematics, compatible with your RJ45 wiring ? (Data, +5V, GND, +15V power) Thank you

Yes i do connect ps Tonight I will start to re install full new Debian wheezy with last drivers on my sheeva Maybe problem with pl2303 driver (unstable) Also stability issue with digitemp :-(

Hello again I move forward. I tried to install owfs on a sheevaplug computer with Debian Squeeze. Seems to work with my DS9097U and Serial-to-usb adapter. I can read 1wire lan value But when I replace the DS9097U serial interface with the masterhub serial interface, owfs does not work anymore...

Hello Do you think it will be possible to publish Plc HTML source code ? I have release 3.00.07 release Thank you

Hello Eric When I connect the DS9490R USB, I can manage my 1-wire network on my synology DS211. I found owfs compiled for it. I have a 6 ports master hub with serial link. I would like to connect it via RS232-USB adapter to my synology to extend to more networks (star) But I don't know which...

Hello I tried with 4700ohms resistor but measure drops to 0% always Then I increase gradually the resistor but when I get again correct measures, the sensor is still saturating when reacing 100% and drops to 0% again... I think there is a problem in the firmware Thomas

I will try but strange as all Dallas temp sensors are together and some give stable values and others fluctuating value

Thank you. I will add this resistor between sensor output and ground to test. Please note that I have also some strange fluctuations with DS1820 Temperature sensors: the value changes +/1°c every measure. have a look on "T1" https://cosm.com/feeds/80285 I don't have this behaviour on all...

Hello I have a domestic HVAC system in my house. In my basement, I've installed the Honeywell HH4000 sensor in the pipe that takes the wet air from bathroom (+/-15m far away from bathroom) This sensor is connected to webcontrol Humidity entry. I measure, when we take a shower, an increase...

Hello I wonder how the web control can be used to count pulse going out energy meter ( 1 pulse per w/h) or water flow meter (1 pulse per liter ) I,Owen an 'old'' PLC without pulse function. Is that possible on multiple RTL inputs ? I have many pulse counters needed How is it possible with the...

Hello Do you know good Humidity sensor to replace the expensive honeywell 4000 serie , working fine with the WC board ? Thank you Thomas

Very interesting ! Can you share this code to perform the logging ? or is this a commercial product ? works on php + mysql ? RRD ? I have already configured all the hardware (DS Themo probe, relay,...)