Search results

Thank you Wayne, I'll try to find small wall wart transformer. The back of my main receiver is realy full of wires!! Stef.

Hi, I'd like to detect the power status of my 2 receivers and my 3 cable box. They all have a switch power plug on thier back. I already have a few cat5 runs between the receivers, cable box and my wiring panel. I want to connect this to either my Elk M1 or my SECU16. They are both connected...

I use a Fujitsu 3400 and I voted for "PC based touchscreen". I screwed up too :)

It would be nice to interface those VW with the ELK M1. If you could force the roomba to go into a particular room by turning on and off VW, creating a trap to force it in that room for x amount of minutes before inverting the process and forcing it to return at it's base...

I witness this also. Only one time a few weeks ago.

Hi Mike, Thank you for the information. I think I will go the Xantech 795-20 route. Where should i buy this? I had to build a small circuit (From Guy Lavoie) to connect the 5v ocelot output to my 9v connecting bloc. Xantech products look like they work with 12v. Did someone ever connect...

Hi IVB, I already have all my IR controled stuff with IR stick-on. Guy: Merci pour l'info! I think that I need the SECU-IR too. Anybody want to trade a SECU-IR for a SECU-16? I don't need it anymore since I now have a Elk M1. Frank: Your product seem to do exactly what I need. But for now...

Hi, I used to control all my A/V stuff that are mostly installed in the living room from my Ocelot. I also have an IR network with IR sensor outside the A/V cabinet. The output from the living room cablebox was also feeding the kitchen TV. On the boxing day I bought a new Sony HD TV with an...

That was the anwser!! Thank you very much IVB. Stef.

Hi IVB, Give me 5 minutes, i'll try that!

Hi, I need to temporary unplug my Elk M1. I did that this afternoon. I had connected it to the telco with the RJ31X. Now that the M1 is unplug, the phone is'nt working anymore. Is there a way, without removing the RJ31X to make the phone work again? Is it possible to put wires across the...

Hi BSR, There is a 2.2k ohms resistor connection to the panel since at least last week. The M1 keypad never stop showing the output 2 trouble messages. Yesterday, I have upgrade the firmware, hoping it would help. When I tried to connect my Ademco wave 2 siren to the output 2, there was...

Thak you BSR, Like Spanky said, any resitance up to about 4700 ohms will satify the supervision current. Question: Does a 2.2k ohms resistor is ok? I think it should be ok since it's less than 4700 ohms...

You are right Digger, Sometime, I take for granted that I must be ok and I'm not. But in that case I look again and again and can. Here is a picture. Stef

Hi, I just verify again and I have -13.87v between - and + of the output2 terminal. I tried connecting a 2.2k Ohm resistor between the - and + of output2. The Output2 trouble message continued. :D Do I need another kind of resistor? That is the only problem I have with my Elk... Still...

I did a measurement and mine was showing a bit over 13v if I remember.

Hi Spanky, I decide to remove my Ademco Siren for the moment. Now I have the Output 2 Trouble message on the keypad. According to the installation manual and other post, I place a 2200 ohms resistor that came with the M1 accross the Outpu2 connector. I still get the message, even after...

Hi, A friend of mine gived me an unused Ademco Wave 2 indoor siren. When trying to connect it to the out 2, i notice that there were current. I need help! :-( I don't know how to connect it. Here is a link to the siren description. I taught I only need to connect negative from the M1 out2 to...

Thank you Spanky! I'll try this tomorow. It's too late now as everybody except me is sleeping :D

Digger, I looked in ElkRP and there is no rules.