Jump to content


Photo

[ISC] 2006 West Security Expo


  • Please log in to reply
4 replies to this topic

#1 BraveSirRobbin

BraveSirRobbin

    Cocoonut

  • Moderators
  • PipPipPipPip
  • 7019 posts
  • Location:Las Vegas, Nevada
  • Experience:guru
  • Software:Main Lobby
  • Hardware:CaddX, Elk M1, Ocelot
  • Tech:X10-RF
  • Video:SageTV
  • CCTV:analog, ip, dvr
  • Phone:OBi100/110, Ooma

Posted 06 April 2006 - 06:30 PM

I attended the ISC 2006 Security Expo held at the Sand's Convention Center in Las Vegas, NV on April 5. During that time I visited many booths and spoke with a variety of technical and sales people. This information was quickly taken down and will be (hopefully) correctly presented in these review postings. Please be aware that there may be inaccuracies in some details including pricing information. So please, take all this information as a "quick first look" only! :(

Honeywell

I visited the Honeywell Booth and spoke mainly with Daren Orth. Daren is actually with in2networks but was showing his company's product which interfaces to Honeywell devices.

Posted Image
(Click on Picture for Full Sized Image)
Honeywell Products Display

In2networks provides a product that interfaces the proprietary Honeywell protocalls to a common networked interface environment. This interface unit is shown below.

Posted Image
(Click on Picture for Full Sized Image)
In2networks Interface Product for Honeywell Devices

Posted Image
(Click on Picture for Full Sized Image)
In2networks Interface Product (Close-up)

Basically this unit has three interfaces. One to the "keypad" bus of the Honeywell device, one to an RS-232 Honeywell device, and one RJ-45 network interface. So basically to interface say an older Honeywell keypad to your network you would just wire in the keypad bus to this unit and plug the RJ-45 jack into your hub.

Not only that, but these interface units include an imbedded web server that is compatible with the MCE operating system! Also, this unit will work with a lot of different Honeywell devices such as their thermostat line. The interface units can even talk between each other and exchange information between devices.

For instance the Honeywell thermostat would know when the system was armed and could turn the temperature down. When the system was disarmed it could turn the temperature back up.

The "logic" needed for each of these units is programmed via a user interface (also in a web HTML interface display) and uses "wizards" to set this all up. So basically you point to the IP address of the unit and go into either the installer interface to set up the device or the user interface to view the device features. The wizards for the installer interface include a variety of "what if " conditional logic options.

There is no "master" controller in this scheme. The interface units have enough logic power and control to talk to other interface units and will just share the information needed via the network.

The best part, these interface units will only run around a C-Note. Of course you need one interface unit per Honeywell device. But, this gives a user who may own Honeywell products a LOT of modern capability that was not previously available.

Shown below are some screen shots of the MCE interface that is included in the embedded web server of these devices. Future capabilites will include IP cameras as well as lighting interface units for UPB, ZWave, X-10, and Insteon! They also have a touch screen that can talk to these units as well (via Internet Explorer on a CE operating system).

Posted Image
(Click on Picture for Full Sized Image)

Posted Image
(Click on Picture for Full Sized Image)

Posted Image
(Click on Picture for Full Sized Image)

Currently this interface unit is available for Honeywell devices only.

I must say I think this was "the" find of the ISC 2006 West Expo! (They were at the recent Florida show, but I guess nobody noticed them?!?! ;))

Edited by BraveSirRobbin, 06 April 2006 - 06:54 PM.


#2 WayneW

WayneW

    Cocoonut

  • -=Gold Supporter=-
  • 2557 posts
  • Location:Florida
  • Experience:average
  • Hardware:Elk M1, ISY-99

Posted 06 April 2006 - 07:16 PM

I must say I think this was "the" find of the ISC 2006 West Expo! (They were at the recent Florida show, but I guess nobody noticed them?!?!

If this stuff was at EHExpo, they sure did a good job of hiding it. And Elk wasn't showing off their skinned keypads either. ;)

#3 jeffx

jeffx

    Dedicated Cocooner

  • Registered
  • PipPipPip
  • 533 posts
  • Location:CNY

Posted 07 April 2006 - 12:54 PM

Only $100? I have to have one :) This makes me feel a little better about going with a Honeywell security system. I'll have to check out in2nets.com.

#4 jeffx

jeffx

    Dedicated Cocooner

  • Registered
  • PipPipPip
  • 533 posts
  • Location:CNY

Posted 07 April 2006 - 01:04 PM

Did they state when this would be available? I see the ICM was available sometime last year for the Honeywell Apex series (~$200), but can't find any information on the model compatible with the Honeywell Vista series.

#5 BraveSirRobbin

BraveSirRobbin

    Cocoonut

  • Moderators
  • PipPipPipPip
  • 7019 posts
  • Location:Las Vegas, Nevada
  • Experience:guru
  • Software:Main Lobby
  • Hardware:CaddX, Elk M1, Ocelot
  • Tech:X10-RF
  • Video:SageTV
  • CCTV:analog, ip, dvr
  • Phone:OBi100/110, Ooma

Posted 07 July 2007 - 05:38 PM

Thought I would update this thread with the following information on Honeywell's new Internet Connection Module (ICM)

New Internet Connection Module (ICM) for Honeywell’s VISTA Security System Series

Honeywell has announced that its award-winning Internet Connection Module (ICM) is now compatible with the VISTA alarm panel series, one of the security industry's leading and most widely used product lines. Using a Web interface, ICM for VISTA allows users to control security systems from any PC or mobile device such as a laptop, PDA or cell phone.

The ICM for VISTA allows customers to control their security systems remotely and view IP cameras via the Web. The device also can be easily networked with other ICMs that control lighting and heating, ventilation and air conditioning (HVAC) functions. It can help customers reduce energy costs through capabilities such as controlling thermostats remotely.

The technology also offers email notification, a feature that automatically sends emails to customers to alert them of non-critical events, such as a child disarming a security system upon returning home from school or a liquor or gun cabinet being opened.

Honeywell’s ICM has received two industry awards—Innovative Housing Technology Award in 2006 by the National Association of Home Builders, HAHB Research Center, and EH Publishing; and Builder News' The Best Products of 2006. It was also recently named as one of the “seven hot products” from ISC West 2007 by the online trade publication securitywatchinfo.com.

More information is available HERE.

Edited by BraveSirRobbin, 07 July 2007 - 05:38 PM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users