Recent content by DeputyDawg

Update: I checked the system more and found this. The music does not play over the speaker when the system is off or at least it didn’t on this check. 1 keypad works. However, when I unplug it from the back of the EZ-Port the music still plays and only until I hook it back into any of the jacks...

I have a NUVO Essentia Six Source, Six Zone system.  Recently a storm came through and the system does not work correctly anymore.   This is what I've determined so far:   - Turning on main box the Standby Light is Blue - All 6 Zone Keypads light up with all of the lights coming on with each...

Is there a way I can check the status of a X10 XPCR Coupler/Repeater with an multimeter?  If so, how?   TIA   DDawg

I had a RC-100 thermostat several years ago that went bad and replaced it with a conventional thermostat.  I want to go  back to a programmable communicating thermostat.  What is recommended to replace the RC-100 that I can use with my Omni Pro II board and the SnapLink app?   TIA   DDawg

Great input.  Problem solved as instructed.  Thanks for input.    DDawg

Since I still need the WIFI on the upstairs Router as the Time Warner modem WIFI will not work up there, could I put a Hub up there and then connect the Router to it and then connect the DVR2 to the Hub?  This would allow me to port forward from the Time Warner modem downstairs for DVR2  and...

pete_c...I learnt long time ago not to argue with an idiot.  I guess you missed the point I made about you and others helping.  So any further help is appreciated.  Continued bickering is discouraged. Get over it.

pete_c...my feeling were not hurt and my post was not to you.  I was not offended nor "whining".  I'm looking for answers and unlike a lot of you who are experts in networking us folks who use this forum for answers are not looking for talk downs but solutions. You and others have provided good...

Frederick Wilt...I have a Linksys E3200 Router upstairs which I incorrectly said modem.  I have a good general understanding of port forwarding.  What I'm looking for is a solution to see DVR2 External rather than "pot shots" at a perceived OP lack of network understanding.  If I had all of the...

Cobra...Sorry, meant to mention that I tried the 192.168.2.1 for ports 2061 and 9061 with the same "Invalid IP address".  Got same error for 192.168.2.122.

The upstairs modem does have port forwarding for 192.168.2.122 for ports 2061 and 9061.  This is probably why I can see DVR2 internal when logged WIFI into the upstairs modem.  When I try to port forward on the Time Warner modem for the same 192.168.2.122 for ports 2061 and 9061 it gives me "Not...

I have a DVR1 which I can see Internal and External on my IPhone app.  I have another DVR2 that is connected to a modem upstairs which is connected to my main modem from Time Warner.  I know the modem upstairs works as I have a computer on it and can connect to the NET via direct or wifi .  I...

ano,   If I understand your post it would require a special wall switch receptacle, a powerline modem that plugs into my PC, a 36A00-1, and the free PC software.  Using this would mean I have to have my PC on all the time for the devices to work.  All Correct?    But this would mean that I would...

In relationship to this subject, I have a OPII board and Dealer PC Access software.  Notwithstanding, that I'll have to program the software, which I've done with X10 and realize that HLC is a little different I'd like to start with the basics.  If I wanted just to be able via software to turn...

On my OMNI II Pro board I used a PSC05 to interface with my X-10 devices using the programing feature in Dealer PC Access 3.  However, my PSC05 went bad and there are none to be found.  I tried to find a TW523 which is a like module to the PSC05 with the same negative results.   Are there any...