Recent content by philgrocks

Has anyone confirmed that Z-wave long range works with home assistant?

Super helpful! Thanks @Ira and @RAL very much! In the guest house I was planning two M1KP2 keypads. So I thought it would be easier to have the M1DBH as a Hub for the zone expander and the M1KP2 keypads. Great to hear both ideas. Gives me confidence I can make this work.

Hi Everyone, I'm looking at a new install of the ELK M1 system in a large home and guest house. House: - Locate M1 - Add a M1DBH for the house keypads and a M1XIN for extra zones for the main house Guest House - Add M1DBH for the Guest house keypads and a M1XIN for the zones in the guest...

Hey everyone, I'm in process of building a new house. I am planning on using Home Assistant... I have searched everywhere, but I'm not finding a couple of things :-( 1) The HVAC contractor has recommended installing a Bryant Evolution (Similar to Carrier Infinity). I have found...

Hi All,   I searched around and didn't find an answer :-(... So apologize if there is and answer I could not find it.   I have snap link on my phone, has been working well...   I made some changes to the OmniPro II system and wanted the new names.  So I tried to retrieve setup... App crashed.  ...

My text messages come thru. But I’m using T-mobile. If you have friend on another carrier I would try that to see if that is working. I am guessing what Verizon does. Does the email address your using work from other email? If it does, then verizon is probably blocking this sender...

I plugged the cavity... Didn't make a difference.   HAI suggested I use Zone mode (although that should not be required) and since doing that my system has been working properly.   Negative side effect is that I loose the ability to engage 2nd stage heating :-(   In the bay area this is not...

Thanks for the comments and hints.   I'm still communicating with HAI on my problem... They asked for a bunch of data which I gave them including my pc access file, etc.   Consistently I only have two omnistat 2 that have this problem.   And let me be clear again... I talking about overshooting...

That's not my problem. I'm using the Honeywell zone controller. It is compatible with standard tstats. Like I said the system worked well for 10 years with the original omnistat model.

I replaced my original omnistats with Omnistat 2 and now have a new problem that is super bad.   The Omnistat 2 continues to call for heat well beyond the set-point.       One day one room got to 93 degrees!   The omnistat didn't show it was calling for heat (it was set to 68 degrees).  I used...

I just found this posting.   I have also seen some very odd behaviors if the Omnipro II has some sort of network connection problems (like when power fails).   Control pads not working, alarm arming / disarming, strange messages on the console, relay switches (on the expansion board) opening and...

Thanks!!!!    Posting here for others.     Omni Notifier Setup Guide Recently, some mail service providers such as Gmail and Yahoo have ceased support for SSLv3, utilized by the Omni Notifier for sending email messages. This can cause notifications to cease being delivered as intended...

I got a response from HAI / Leviton Tech Support.    The suggestion I got was to disconnect the RC2000 a few minutes and try again.   I disconnected the RC2000, waited 20 minutes.   Then reconnected.   After this both that were wired up returned to normal operation.   I then installed 3 more and...

Indeed I checked the jumper and it is on.   What is also strange is how two thermostats used to have the address and humidity and now that is missing.   I will have to see what HAI / Leviton says.

Hi Cobra,  Thanks for your post.   Yes, all new stock.   They were drop shipped from Leviton.   The serial numbers were all in sequence.  Some in the middle of the sequence worked too.   Yes, all connected to the Omni Pro II.   I use the Honeywell zone controller, and these thermostats for zone...