Recent content by martytess

I have the same issue. I have set up my cameras on other systems but NQLink is more difficult.   Anyone have success?

Thanks for the reply, I am new at the automation end of things.   Can you give me an example of a pause and how to group?    Thanks.

Hello again, long time no posting for me. I got the house up and running in a basic state, now its time to do some fun stuff and automate.   I am trying to create a "Morning" scene. I have been able to get all of the lighting to do what I need to but your ingenious shade programming has proven...

No, I will pick one up...BUT If I come out analogue how do I go into HIFI 2? as a source? Then program when door bell then switch source to wherever it is plugged into?

I picked a canned message "hello" from the list, thendid the following automation:   WHEN doorbell secure THEN say "Hello".    I hear nothing. How do I send it out HIFI 2? There is no option to configure where it outputs...

For me, the easy part is getting the recording in!   Can you please step me through how to select an audio file from within PC Access?   I cannot figure out where the "blank sound registers" are. Are those the "Voices" and if so, how do I load a sound file into one of the "Phrase" slots or??? I...

My question on the doorbell was not on the trip side but the trigger side. How do I get something to come out of my speakers via HiFi 2 system such as a Mp3 or some kind of sound. How is this normally done? I have a PC on the same network that could play the Mp3 over the HiFi 2 but how would I...

 When you say "the default fade rate programmed into the light switch", would that be with a RadioRA2 switch or only an HAI switch?   I will try the "Bright" command.   Other issues you may have experience with that are baffling me:   Today I was trying to get the doorbell switch to trigger a...

Here's another one...I have 2 exterior cameras that have motion sensing capabilities. The lights shutting off abruptly is triggering the motion sensor so they are stuck in an endless cycle. To fix this I need the lights to gently fade. How can I get a automated fade? Set light level to 80% for 1...

Sorry for the late response, I finally had time to try this (I have a 2 and 5 year old that keep me running...) and it works perfectly!   I then stared at it for about 20 min, was writing you that I have no idea how this works and then the light bulb above my head came on. Another ingenious...

I think Experience level: Average...Needs an update...   That toggle was ingenious and will make my situation twice as good, even if the holy grail "scroll" cant happen...   PS, wait til you hear my other programming issues : O   Marty

I tried this, it does not work as was the problem in my first post, it steps through all three steps at one button press (0 to 1, 1 to 2, 2 to 0 ).   WHEN HotTub6Btn SW5 PRESSED     AND IF HTubEBlind CURRENT VALUE IS 0          THEN SET HTubEBlind TO 1         THEN SEND HTubEOpen OUT SERIAL 3  ...

Does this look correct? Seems I am back to the original problem as there is no option to set a delay on a flag value.     WHEN S'sRm 6 Butn SW5 PRESSED     AND IF SWBedBlind CURRENT VALUE IS 1          THEN SET SWBedBlind TO 2         THEN SEND SW Bed Blind Closed OUT SERIAL 3   WHEN S'sRm 6...

Thank you! you are a wizard!   I then added the triggering of the serial out, the RadioRA button and it works perfectly!   WHEN Hot tub North Blind WHEN HotTub6Btn SW4 PRESSED     AND IF HotTubNBlind ON         THEN Hot Tub Room ON FOR 1 SECOND         THEN SEND HotTubOpen OUT SERIAL 3   WHEN...

I am integrating Hunter Douglass shades with a Omni 2 Pro and Radio RA2. The issue is that Hunter Douglass only gives serial command control to choose a preset scene. So to make even a simple open/close takes 2 buttons, I am dealing with many more features on the shades like top down bottom up...