hai omnipro

I have Universal MX-3000 remotes all over the house that using a MSC-400 send serial commands to the OMNI. The system worked great for years until X10 just completely quit altogether. I never tried to use the remotes to control anything for years since the X10 was so problematic. Now I want...

I don't suppose anyone has any good way of syncing the clock on the HAI OMNI? My clock is off minutes a week. Drives me nuts having to correct the time all of the time. I've played with the adjustment, but it doesn't seem to help, maybe I just need to play with it some more. I'm a bit...

I just can't seem to get my X-10 to work anymore. Tried new serial modules, phase coupler/repeaters, nothing it getting through anymore. I'm looking in to Z-Wave, but is the Leviton VRC0P anywhere to be found? I'm dead without it. I want to use the Omni IIe to be the controller. Is this...

Noticed a lot of HAI Omni expertise on this site! Hoping I can get some help …. Bought a house last year with HAI Omni Ii system, I’d like to use the “Myro: home” App to connect via WiFi instead of the touchscreen. Is the Myro: Home app good for Omni II users? If so, I’d like to get my...

I recently stumbled across this article which shows how you can integrate zones with termination resistors higher than 1k. It works for termination resistors >1k to 3.7k. This means Ademco/Honeywell, Elk and others. The article is at: http://kb.homeauto.com/default.asp?id=924&SID=&Lang=1 dwalt

I've read through a number of the threads here with similar problems, but none of the solutions seem to have helped me. My board out of the blue stopped communicating with my HSC3 pi and I've been trying to track down the issue. The red light on the board stopped working. My first stab was...

Hello, We are working on a huge project and was wondering If you had any ideas on how to program the relays (just a add on 4 port relay board 10A07-1) in a Omni Pro II so we can determine direction of a car entering and exiting a driveway. The goal here is to voice announce that a vehicle is...

Hello All, I have purchased home that has an Omni Pro II system with HAI switches and all we were handed was the owners manual and tech support line that is no longer in service. The last owners did not know any of details on the system and the room names on the wall panels are from the...

If there is a cheat sheet for this it would be great to know where to look. So I PCA software but it won't fire up with my saved PCA file on another computer. So it looks like I need to pull the pca file off the board. I have a serial/ethernet cord. Do I plug it into the ethernet port on the...

Hi, I'm a new member here. My google searches always bring me to this forum! I have the OMNI LT with an expansion board, have some modules from OnQ, HAI, Honeywell, and others and have the system monitored with Alarm Relay. I just recently replaced an outdoor temp sensor with a temp/humidity...

I'm using the snap link app and can no longer connect to my Omni Pro panel? About a year ago, I installed a new Router (Fritzbox) and changed my IP on the panel to 192.168.178.2 to suit the range of the router. My Routers IP is 192.168.178.1 Its worked finer for a year or so but suddenly....no...

Hi, I’m trying to find/buy an OmniTouch Pro license and can’t find one anywhere! Anyone know where I can find one? Or does anyone have one I can use? Thanks, Nick [email protected]

Hi, Just installed my copy of PC Access and tried to update it. Has Leviton shutdown the update link, can’t download board firmware, omnitouch firmware either. Anyone else having the same issue? Thanks, Nick

I am looking at possibly replacing my Omni Pro II system with a newer alarm system. I have had the system since 2005 with the entire house; doors, windows, motion sensors, and sirens, hard-wired into the control panel. I also had it set up to cover both my home and pole barn (each with their...

Starting OmniPro ll without council. I believe my Consol is dead and I don’t have another is it possible to start up a panel with access by PC or Myro?

Greetings, I'm happy to have found this forum. We purchased a home in North East San Diego County last year. The home was built around 2009 and the original owner put an extensive HAI system throughout (4000 sq. ft.). During this time, there have been a number of times I've woken up in the...

My understanding is that the OmniLink protocol is used for communicating with the Omni controller via its serial ports (RS-232 & RS-485) and OmniLink II is used to communicate via its ethernet port using TCP. However I’ve also read in this forum that UDP over ethernet is also supported but I can...

Here using Home Assistant (and Homeseer) to manage a Ring Alarm (and doorbell and thermostat) for house #2 and OmniPro2 panel in house #1. I see an console keypad for the Ring Alarm system but do not see one for the OmniLinkBridge app. Ring card is defined as: type: alarm-panel states: -...

  Issue Background: Stable HAI OP2 (4.0B) in place for 10+ years with no changes to hardware/software in 2 years.</li> While away on vacation I received Omni Notifier message Freeze Alarm &quot;FREEZE ALARM TRIPPED</li> 5 minutes later I received Omni Notifier message ALARM RESET</li> It's the...

When we built our home, I hard-wired the security panel with 30-40 zones using 1K EOLR at the end of that zone.  I'm afraid my current Leviton OmniPro is on it's last leg.  Since Leviton has discontinued the OmniPro Panel, I was curious if anyone knew of a security panel that used 1K EOLRs?  I...