Recent content by Douglas

A quick update, finished re-wiring tonight and started programming. Here are my steps for anyone else who has to do this: First thing I did was to change the encryption key in the new OP2 to match the old OP2. Left the default IP of 192.168.0.101 so any of my IP devices wouldn't find the new...

If the old programming can simply be "pushed" into the replacement controller, that would be great. I was thinking each OP2 was tied to it's code somehow, such as the MAC address or serial number of the board. Or maybe even those 2 MAC-like security codes you have to put into the 5.7e to get...

I am the last person to program the panel, I have the PC Access, and I have the lastest "profile" saved. I believe I have the latest PC Access version, and the OP2 was also at the latest version. Good question about the keypad, I believe it was working fine (even though no ethernet/serial...

Thanks for the responses, similar problem to others, ethernet port is intermittent, serial ports don't seem to do anything or it's not running any of the programmed code. I made a crossover ethernet cable, and direct PC to Omni pings are still lost (and high jitter rate). Unplugged ethernet...

Does anyone know if this actually happened? Repair of Omnipro 2 main controllers? Mine went on the blink a few days ago and I've done a little troubleshooting, I'm afraid it needs real repair. I did the RAM reset, I will try the eeprom reset next. If the controller can be repaired, I am...

No response from Leviton today, I'll try the 800 number tomorrow. The website says 800-722-2082, I assume that's the number you called.

Thanks for the info, I just reached out to them via email. Which Atom based touchscreen are you using? I would imagine many things run faster than the 5.7e! Thanks again!

Pete - I've been on the hunt lately for OmniTouch Pro again and came across your post from 6 months ago. I see where you called Leviton and they said the OmniTouch Pro software is now license free - but where do you get that non-license version? Or did you call them back and they changed their...

I too am a long-time purchased "pro" user, and just discovered all of this last night. I use the app maybe once a month, either when I'm outside (to turn on lighting) or just too lazy to get up off the couch(!). The app worked well, now it crashes when I simply try and select a thermostat...

Hello All,   I'm trying to do some "convenience" updates to the old Omnitouch 5.7e's, and it's been quite a long time since they've been altered.  Automation Studio has a few nuances and glitches to get things just right... and I'm sure this is just one of those.   -  In HAI Automation Studio...

Just a minor bump on an old topic, about 2 weeks ago I noticed that the motion sensor on one of my RC-2000's stopped working.  That is, you wave your hand across the sensor on the stat and the backlight does not come on.  I wasn't particularly worried, not a feature I use on that particular...

I didn't even notice this thread was that old!  So now that someone brought it back to the top, what was the final solution?

Some ideas...    1. For "party mode" or "rain lockout" a master solenoid on the water source will work well.  It isn't an independent zone on/off control, but it does solve certain problems.   2a. I think Pete is correct about the trenching machine, I've seen the one that looks like a ride-on...

In my experience, I've used the 8-button house status switch in two ways - as a "scene" controller and as a "room status" switch.  This is how I understand it works:    - The "scene" controller is just that, you push a button and a lighting "scene" is activated.  If you set one of the regular...

I never looked at a schematic for the serial port tap, it's a very simple circuit.  I'll have to make myself a cable with a toggle switch so I can pick which side I want to monitor (or both).  I can't believe they get $189!   As a side note, I've used a fair amount of B&B Electronics serial...