Recent content by elias1693

Recenlty upgraded M1XEP to FW 2.0.34 and now my ISY will not connect to my Elk M1 which means my rules arent working. I havent changed any passwords or anything else. When I click on the ISY ELK configuration tab all my settings are correct and port 2101 specified but when I click on enalbed it...

My Elk has been working great for about a year. I have dyndns setup on my Cisco\Linksys router and when I type in my dyndns name address or external IP address it connects straight to my Elk and prompts for USER ID and password. Ports, 80, 2601, and 2101 have all been forwarded to my M1XEP.   ...

Same thing was happening to me. I would connect... it would take longer than normal and then within 30 seconds it would immediately disconnect. It was driving me crazy. For two weeks I couldnt figure it out. As soon as I read the first comment from Matt above about his BTW comment and his ISY99...

I just got my elk M1 Gold system up and working and monitored. I have also recently purchased a Denon AVR 3312CI and was wondering if it is possible to connect this and add it to the Elk M1 Gold to start a home automation project. I have read forums of others doing this but I am wondering what...

M1G Hardware version .13, Boot Version 3.3.6, Firmware Ver 5.2.8 M1KP Hardware version 010, Boot Version 3.0.14, Firmware Ver 2.1.48 M1XRF2H Hardware version 4.1, Boot Version 1.0.0, Firmware Ver 0.9.8 M1XEP Hardware version 1.0, Boot Version 1.2.0, Firmware Ver 1.3.28 When I re enter my home...

I've setup a user ID and code for my house keeper. While going through the rules I enabled her access on Fridays during a certain time period. I could not find a way to enable to rule every other Friday. The only choices I found were every Friday. It what I'm trying to do possible? If so how?

Wow thanks for your help FRED. That worked perfectly. I wasnt able get GMX working but my paid subscription through 2MHOST.com worked after I successfully Telnet into it and send email. I also had to make sure the email address I was sending it to was not the one I was sending it from. Whenever...

Thanks I'll try the GMX account. It seems the Lavabit has stopped accepting new users:( Wish there was an Elk Forum page with approved SMTP settings and or approved or known good email providers.

Thanks the DVR is separate and I finally got it working after using virtual server on my dlink router instead of port forwarding. The PIR is in place but I am having difficulty getting email to work on the Elk M1 Gold. I've been on forums for a week straight trying different methods and still...

Windows 7 64bit Elk M1 Gold M1G Hardware version .13, Boot Version 3.3.6, Firmware Ver 5.2.8 M1KP Hardware version 010, Boot Version 3.0.14, Firmware Ver 2.1.48 M1XRF2H Hardware version 4.1, Boot Version 1.0.0, Firmware Ver 0.9.8 M1XEP Hardware version 1.0, Boot Version 1.2.0, Firmware Ver...

Never mind I was able to connect it to an rj 45 connector and connect it to the data bus hub. Moved the terminating blank rj 45 connector one slot over and now it is enrolled and working. Love this system!

Are any jumpers or terminators required for either installation on the Elk Panel or the M1xrf2h?

Got my system up and running and this was an awesome learning experience! I have the ELK-M1XRF2H Honeywell Wireless Receiver. Do I plug it into the panel in the lower right below JP3 where the picture of the keypad is? Or can I add a RJ45 connector to it and add it to my ELK-M1DBH data bus...

I will have 13 wired zones. Each zone will have only one sensor except zone 13 which will have two run in serial or parallel (hidden door sensors for french doors). Do I need a resistor on each zone 1 through 12 or only zones withe two or more sensors such as zone 13?

Thanks I'll add the speakers and go with the Uplink 2500. I've purchased a Zmodo 8 channel DVR. Not bad for $300 bucks but not great either. Day time viewing is just OK. Nightime viewing is horrible. Its working on the local network but havent got the iPhone remote app working yet. Tried...