Recent content by SierraTech

I just went through the painful Process replacing my OMNI II PRO 2002 Vintage controller, due to failed Ethernet PHY. I purchased a USED OMNI PRO II (Flashed 4.0B), and can now successfully communicate through the GL.iNet router (@pete helped with this) with good TCP communications. I have been...

Hi Pete! Yes, I plan to wire in a console to see FW version and set IP Address. I received confirmation from vendor yesterday they RESET THE ROM & RAM prior to shipping. I know there were lots of changes to the board, some including a daughter card above U29. My printed manuals are from JAN...

Since I have had Ethernet issues on my original HAI OMNI II PRO, I purchased a USED updated controller, with the FLASH (EAROMS) under U29 & U30. It did not come with a manual, and the only manuals I have from many years are based on the old design I purchased in 2001 (USES EPROM). Does anyone...

The version I have is 3.17.3.861 which Leviton released to fix Date & Time issue in 2020. By the way Malwarebytes Browser Protect Cautions the download?

I have purchased several PCS UPB Receptacle Modules (15 AMP) the last three years (unfortunately I haven't had the spare time to install and implement). I have been a fan of the application notes they have on there website geared to PCS/OMNI II Integration. I need to address the lack of...

Not complete convinced jumpers are the issue. I just was messing with DMZ router for OMNI II Network Interface and SMOKES had trouble again. I moved Power Supply for Gl-iNet Router to first Auxiliary 12V power screws, and now loop is reporting good. Something seems intermittent with the OMNI...

I think I found the issue...... Some time ago I strapped Zone 3 & 4 for "NORM", and left ZONE 1 & 2 for "SMK" (JP11 & JP12). I decided to put JP11, JP12, JP13 and JP14 all in "SMK" position, since I already moved Water Moccasin sensor to ZONE 33 (Expansion). I wonder if any zone, between 1...

Well no answer, but below is a list of steps I have taken: 1) Replaced EOLR with New One, I didn't think this would help (it didn't). 2) Moved ZONE-1 to Zone 2, no change Loop still reading "4" (Zone-1 used to read 33 when working before adding Water Moccasin Zone-3) 3) Removed ZONE wires from...

Greetings, I reconfigured ZONES 2-4 as "NRM" quite a while ago, with ZONE-1 dedicated to 4W Smoke Detector Loop (SMK). I connected Water Moccasin contact closure on ZONE3, and then after powering up the panel, My Smoke detector loops shows "Trouble Now". I since moved relay contact to Expansion...

No, it still reports APP needs to be updated.

Sounds like a intermittent component on Main Board. I always had problems with Output 1 never working, and even after sending in to HAI around 2004, they made some upgrades to board, never fixed Output 1. One other suggestion, you might pull EPROM (or EAROM) and re-seat. Again, sockets are not...

Any specific zones generating false alarms? Is the zones associated with Main Board, or Zone expander? I recently added a new expander, but haven't wired to it yet but one thing I noticed is the headers were never Gold Plated, just wondering if this might be a potential cause. Otherwise possibly...

Well that's interesting! I have left the app in place, but my iPhone 6S won't be getting iOS 16. I wonder what has changed with iOS16 that allows the app to run. Thanks @charliebarns for sharing this. I will be curious if iOS 16 updates continue to allow this.

@pete_c Don't you hate that? My Zyxel router has two firmware images, good thing because newer version broke WiFi calling on iPhones, and I had to switch back to previous firmware image at 11:30 PM Friday before Labor Day weekend to make a Cell Call to owner (I'm local point of contact) of...

Thanks for the reply. This is not a Cable modem, it's AT&T Fiber (PASSTHROUGH). I don not allow UPnP anywhere, due to security risks. I'm short on time today to research further, and will review your questions and @pete_c post. Just wanted to acknowledge I appreciate the information and will...