Recent content by computernerd

  1. C

    Elk M1G firmware upgrade broke M1RB

    I recently upgraded my Elk Firmware to 5.3.10 and I cannot get the M1RB output to work anymore?  The M1RB J1 is connected directly to M1G J16.   I tried to turn on the output zone and the light does not come on one of the zone on the M1RB board? I also tried to use the script in the Elk M1G and...
  2. C

    Elk or Homeseer to use cell phone to call when alarm goes off

    When someone cuts the phone and/or cable line outside the house I want the Homeseer or Elk System to use the cell phone to call me that the alarm is going off or report a problem.  I don't want to use a cell phone with a data plan since I only want to call to report problems and cheap monthly...
  3. C

    GRI 2600 water sensor issue

    Okay what is the best power device (Altronix or other brands) to use so that I can replace the PD9?  I am planning to add 6 more sensors in the future. 
  4. C

    GRI 2600 water sensor issue

    Thanks for the input everyone i might be getting closer to the problem.  I unplugged everything from the sensor to get the elk to reset the "Violated" to "Normal" status.   Then I hooked up everything again and i still  have the "Normal" status but when I put a wet paper tower under the sensors...
  5. C

    GRI 2600 water sensor issue

    I tested the voltage between the red and black wires on the ELK-PD9HC 400mA and it shows 8 volts.   It looks like the Power supply is not supplying enought power to the ELK-PD9HC 400mA device? I am using the Avemia AC/DC power adapter model PA1A1D which shows 12volts on the adapter.   The GRI...
  6. C

    GRI 2600 water sensor issue

    I did remove the resistor and setup the elk to use closed only. This still does not work.
  7. C

    GRI 2600 water sensor issue

    I am not able to upload a image to show you since this board requires a URL for the image to upload it to.    I have 1 2200 ohm Resistor attached to one of the zone 13 neg input and the other on zone 13.  
  8. C

    GRI 2600 water sensor issue

    I hooked up the Gri 2600 water sensor to the ELK-PD9HC 400mA and the zone to the elk m1g. I keep getting a violated message on the zone. The Red wire was attached to the positive and the black wire was attached to the negative on the ELK-PD9HC . The other two was attached the elk using a...
  9. C

    ELK-M1RB hooking up with garage door switch

    Thank you for replying.
  10. C

    ELK-M1RB hooking up with garage door switch

    I ran a Cat5 cable from the ELK-M1RB to the Garage door switch and I don't see the light blinking on the ELK-M1RB board. I can use the ELK-M1RB output to open/close the garage door but the ELK-M1RB board light does not blink? Does it not have a enough power?
  11. C

    Elk sending temperature to RC-80B - HAI Thermostat?

    How do I write to this register using the Elk M1G? Can this be done using the rules?
  12. C

    Elk sending temperature to RC-80B - HAI Thermostat?

    This looks like it is possible, How can I get Elk rules to set and send the Registers to the thermostat? Has anyone done anything like this and how? It would be cool thing for some of us that wanted this feature.
  13. C

    Elk sending temperature to RC-80B - HAI Thermostat?

    Can the Elk M1G have rules to send the outside temperature to the RC-80B - HAI Single Stage Heat/Cool thermostat?
  14. C

    UPB with SA USR slave problem

    I realized that this a California wiring setup and UPB will not work with this. Is there anyway I can hook a dimmer to the Elk M1G? I appreciate any help on this. Thanks
  15. C

    UPB with SA USR slave problem

    I have a USR switch with US11-40-W switch and I cannot get the lights to come on. I think my light configuration is shown on the link below. http://searchwarp.com/swa66434.htm I had the US11-40W working but when I put the USR switch it stopped working. Here is my configuration US11-40W...
See more
Back
Top