Recent content by pac1234

How wire output from NVR into the Omnipro II ? (attached drawing of correct wiring?)   NVR Hikvision DS-7716NI-SP/16  (NVR) Program setup - Default status: Low Level (Greyed out and don't think I option to change this) - Triggering Status: Pulse (Greyed out and don't think I option to change...

How wire output from NVR into the Omnipro II ? (attached drawing of correct wiring?)   NVR Hikvision DS-7716NI-SP/16  (NVR) Program setup - Default status: Low Level (Greyed out and don't think I option to change this) - Triggering Status: Pulse (Greyed out and don't think I option to change...

Did get a response on this yet ... anyone know where I might get help on the RSC KPL7 programing?

I can't get the RCS KPL7 to do the initial handshake with the OmniPro II (3.9)  Presently Im getting the alternating blinking LEDs ,  "OPERATION : Upon power up the KPL7's LED will sequence and then settle into an alternating flashing pattern indicating that the unit is waiting for handshake...

If you mean did I "write to controller", the programing above ... Yes

Yes its set to Pro-link, 9600 rate

Hi reaching out on this one again, on how to program the RCS KPL7?  Looks like I have the switch wired correctly form info above , but can not figure out how to program?   The switch I have addressed as #1 (binary on/off/off/off), and KPL7 is connected in serial port 3. (RS485 correct jumper...

Found this on the Novo Solutions HAI Knowledge Base http://kb.homeauto.com/default.asp?id=951&SID=&Lang=1   KPL-7 Scene Switch Installation Tips The following tips can be time saving in the proper setup and operation of the RCS KPL-7 Seven Button Scene Switch...

I can't get the RCS KPL7 to do the initial handshake with the OmniPro II (3.9) and not really sure how its done? Presently Im getting the alternating blinking LEDs   Setup in PC Access (v3.15) Setup / Expansion / Serial : - Rate "9600" - Function "Pro-Link"? (is this the correct function?)  ...

Have a Hikvision NVR DS-7716NI-SP POE NVR and have all the cameras hook up directly to the NVR. One camera DS-2CD2432F-IW, has a PIR sensor for detecting motion. The NVR seems to only have settings to set the camera, with motion alerts, based on changes of the pixels in the field of view.   Am I...

Hi,  Have an Omni Pro II with wired indoor motion sensors and ALC lights ( no wireless sensors). Just installed a Hikvision IP camera/POE NVR system and happy with it except the motions sensors react to everything including moths flying in front of the camera at night. So can't use as planned...

Adding a door intercom (Channel Vision TE-111), where when someone rings the front door bell all the house phones ring with a distinctive ring.  Have a HAI OmniPro II and not sure which of the following below is the correct spot to splice it in? Do I place the TE-111 before, after, or in...

Adding to thread above - for example if I just streamed 4 cameras at a time      Camera Stream -  H.264 Vid Quality - Med Frame Rate - 30 # of cam - 4   Bandwidth  25 Mbps   Are these systems flexible enough to remotely choose which camera to stream? For example from my iPhone choose only to see...

Hi thanks for the info and the calc! Really helps in understanding the limitations, using different variables    Camera Stream -  H.264 Vid Quality - Med Frame Rate - 30 # of cam - 16   Bandwidth  100.29Mbps   Is it an option with the iPhone apps /NVRs to stream just one or a couple of the...

I have heard that IP cameras have the disadvantage that they can congest your network.    Some NVRs have ethernet wires that connection directly to the NVR. So I'm assuming that, if you have a 16 channel NVR, and have all 16 cameras connected directly to the NVR,  there is little load on your...