Recent content by shadowhunter

I would say the cable is no more than 15 ft from the hub to one side of the sensor. From there it goes up to the roof to the weather station. Near as I can tell the voltage on the pins is between +4.5-5v. I made another change to the setup. According to what I found using the 1-wire viewer...

Eric, In the past after the the wind spike reading yes, the lights would be blinking out of sync. That is usually when the readings for everything but the Baro would flat line. What I have seen under normal operation is that the lights on the channels that I have hooked up would be solid...

Eric, sorry for the late response... There was a pretty fair ammount of lightning associated with the storm yesterday, however in other storms I don't think there has been as much lightning (I am usually not at home when they happen) and the same thing happens. In past it would cause the other...

well I guess I can rule out the hub, since we are having a nasty storm right now and I just had a spike up 94 MPH.

I have been noticing some interesting things since I added the hub into the mix. When we have t-storms that involve higher winds, i will receive a spike in the readings to +/- 90 MPH for one or two cycles and then it returns to what the normal winds are at. I have heard differing opinions about...

I think I just broke the Baro :blink:, I hooked up the baro while trying to test the channels in the 1-wire viewer..... and started smelling that electronics burning up smell.... I opend the case and noticed that there is a definate burnt mark on the baro board looks to be on the 2 regulator...

Eric, I am not seeing any ROM ID's when using the 1-wire viewer :blink: I have re-done the ends of the cable running from the PC to the "Main" port on the hub twice and it hasn't changed anything. The only LED on the hub is the green power LED. I have added the jumper back to the Temp/Hum...

eric, I recieved the hub and baro the other day, thanks agian!! one question though, it there a ROM-ID assigned to the HUB? The 1-wire viewer is not picking one up, and apparently Weather Display needs one. Everything seems to be working okay except for the Main #1 Chanel is not lighting...

eric, no biggie, was just currious. Can't expect you to work 24x7 now can we :lol: I am willing to wait for quality parts and applaud your AWESOME customer service. Keep up the great work!! I just noticed the new logo on the site, I like. Thanks, Jim

eric, Sorry for the delay in response, I did not receive the normal email notification that a response was posted. How about something along the lines of 200x70 for the gif file, I think that should be good. As for the order, just currious as if something is out of stock, per the last email I...

eric, Thanks for the fast response!!! (unlike mine :D ) Your explination is awesome and clears up quite a few things on how everything works together. I am going out on a limb and assuming that the jumper on your devices is what enables or disables the onboard voltage regulator for the...

I am getting ready to place another order, but have a few questions. My current set up consists of a H-B V3 weather station, and a H-B Temp/Hum sensor. I am planning on adding a barometer and a rain guage to round out the basic weather station set up. My questions(s): Regarding the hub, how...

Thanks for the info on the jumper. Since I forsee a hub in my future I assume that I would remove the jumper in the weather station and add the jumper back to the board when I add power. Thanks Again for the fast shipping and awesome support!!! Jim

Just received my Temp/Hum sensor and have a stupid question about wiring it. Since I am not powering the newtwork at this time am I safe in assuming the sensor can be daisy-chanined to the rest of the network by putting both sets of blue and white wires into the screw connector, or would I be...

First of all I must commend you super fast shipping, Bravo!!! I just purchased one of your V3 1-wire wind devices. From reading your sensor wiring instructions it states that if I wire the cable according to your design I should remove the jumper from the board. ".....or a cable wired...