Recent content by sky-chicken

Good morning, what happen to you is that after resetting the USB you created a new ZWAVE network with a different address and you did not backup the old one in Thinkessentials. What you have to do is; RESET THE usb STICK AGAIN TO MAKE SURE THERE IS NO OLD DATA ON IT: JOIN THE USB STICK TO YOUR...

the problem with Ultramon is that this takes alot CPU power because the cloning / re-scaling is done per software.

I have over 40 bulbs replaced in my house with this brand. I bought them on eBay for $2 per bulb including shipping and last week I bought them at Saveway for 50 cent per bulb. The color is clear white and change after a couple days to light yellow so you can not tell the difference between the...

I am using the 7600 nvidea with dual monitor (touchscreen 1080p) and 65" Sharp in "nvidea" clone mode with Windows Vista Ultimate and I have to say "what a nightmare" 1) My TV is connected to an 2x4 matrix switch (monprice) but this does not matter. 2) everytime I turn my TV off for more than a...

I am using this setup in a mix with the new Vizia RF+ 2 way switches. the first 10 ID'a are Zwave and from 11-to 30 are ONQ ALC with ELK OnQ interface module. What firmware are you using on the ONQ ALC internal serial port ?

I am using the controlthink USB zwave controller and I also have one Sylvania controller. Will check if reset the USB adater does the trick.

I am using the ELK-M1 with the ONQ ALC interface and it works like a champ. I tried X10, UMP, ZWAVE and now I am testing VIZIA RF+ and the only working solution is ONQ ALC. By working I am talking about direct feetback to the touchpanel or controller or webinterface. There is nothing else out...

Thanks for the quick reply. I did this before but for some reason after: 1) EXCLUDE 2) Reset 3) Include to the network the new assigned node ID is higher (when it was 10 before it adds the new node ID higher than it was before) I have 4 nodes and now they are 1 (controller) 3 (switch) 6 (RF+...

Does anyone know how to reset a node address on the Vizia RF+ device. I played around with some switches to see how they perform and now the node address went up to 11 and up. This upper address space I use for my ONQ ACL so I need to lover the node ID below 10. Any idea how to do that ?? Reset...

you are using the new 16 channel RTS from somfy. Do not connect any regular RS232 cable or device to it because it will Nuke your hardware (5 volt connector) You have to buy an RS232 to RJ45 adapter and connect pin 3 to pin 2 and pin 6 to pin 3 and pin 7 or eight to pin 5 RJ45 Pinout Pin...

How would the Thinkstick USB replace the RZCOP ? I still need the RZCOP to interface with my ELK-M1. My question was if I still have to buy the Vizia RF+ (VRCPG-SG) remote to program the RZCOP for 2-way comunication or would the ThinkStick do that for me. The main goal is to get rid of remote...

The RZCOP is connected to the ELK-M1 via ELK-M1XP running sw version M1XSP_Vizia_20.0.3_22Aug08.bin (11KB). There re 7 z-waves in the Network: 1) one Vizia RF+ VRI10 (works but no status update) 2) one Vizia RF+ VPR15-LW appliance module (works but no status update) 3) one...

hello J9, I tried your program using 2 Vizia RF+ and 3 Sylvania light switches and the Sylvania master remote. I can add all devices except the Sylvania wall plug in module and the Vizia RF+ 4 button swich. After strting the LumenLink the software reads all nodes and the status of the Vizia RF+...

I am not able to get 2-way comunication going withj the M1 or your software. I am using the Sylvania Master controller and was wondering if this could be the problem. If I power of the elk and power on again I get one status update. One way works just fine but if I change the setting on the...

Did you try Setnetpro.com ?? It looks like they have it in stock