Cobra - this is the standard Z-wave / motorized deadbolt on the inside of the door, and a simple, traditional round deadbolt lock on the outside. From Amazon:
https://www.amazon.com/Kwikset-Signature-Traditional-Electronic-Deadbolt/dp/B013KZRTTG
The only way to actuate this lock at the door is by the thumb-turn on the inside or a key on the outside. My use of the lock is remote lock/unlock control, remote status monitoring (if manually locked or unlocked) - without outside keypad access. The only way to access the door from outside is by using a key, phone app or OP2 programming code.
As for my initial issue, I have corrected it by downloading the latest version of Vizia RF+ Installer software - version 1.1.5.2. I then re-built the Z-wave network (excluded all devices, included locks, then included VRC0P) without issue, and I now get the correct response from the lock. I also re-loaded the firmware in the VRC0P (before I updated the Vizia software) but that didn't make a difference.
Some notable items that may help others:
1. You need the Z-wave door lock, a VRC0P serial interface - that says "RF+ 3" on the back - and a VRUSB Installer tool. You also need the Vizia RF+ Installer software.
2. Install the door lock on the door first. It's tempting to do this entire setup in a controlled environment and then install the lock on the door, and add the VRC0P to the OP2. I think it's important to install the lock and let it "learn the door" before adding the lock to the Z-wave network. With the lock installed and the door closed, remove the battery pack. Then press and hold the lock's "program button" and re-insert the battery pack. Keep the button held for 5-7 seconds after the battery pack is inserted. You will hear/see the lock "learn" the door - like which way the lock should turn for lock/unlock commands. Make sure all this is working and you have a functional door lock first! Monitoring and control is really a secondary function!
3. It is a good idea to have a PC (DB9) to VRC0P (RJ11) cable. Two reasons: 1. firmware updating the VRC0P,and 2. initial testing / troubleshooting.
4. Use either Putty or Hyperterminal to set up a serial connection to the VRC0P. 9600 baud, 8,N,1. In the ASCII setup, check off "Send line ends with line feeds" and "Echo typed characters locally". In my case, my PC has a hard serial port, so I'm not using any USB or ethernet to serial converter.
5. Connect the VRC0P to the PC before you plug the VRC0P into AC power. When you first plug it in, it will tell you what version it is running! I didn't know this, I only found out after I had already "updated" my VRC0P firmware. When I plug mine in now, it tells me: $Leviton(C) 2008 V2.36S/Z-Wave 3.42 If you have an older version number, I recommend updating to this version (it works for both my older Kwikset Z-wave and newer Kwikset Z-wave locks).
6. Plug the VRUSB into the PC before you start the Vizia RF+ Installer software. I am now using Vizia RF+ Installer software version 1.1.5.2. For my use, I started a "new network" in the software. (Note: if the software doesn't "see" the USB stick, it will tell you so in the bottom status bar, left corner.)
7. I've found that brand new locks need to be "excluded" from the Z-wave network before you can add them. (Perhaps they are added to a test network when first manufactured and never excluded from that network?) This was a lesson I learned early on when fighting to add brand new locks to the Z-wave network. Click on the "Exclude Device" button in the software tool bar, then "OK" in the pop-up box - and then immediately press the "A" button inside the lock. Basically you need to be within an arms reach of both the PC and the door lock.
8. Add the locks to the network before the serial interface (VRC0P). Same process as above, click the "Include Device" button in the software tool bar, then "OK" in the pop-up box - and then immediately press the "A" button inside the lock.
9. Add the VRC0P serial interface to the Z-wave network last. To add the device, first long press the LED "button" (the clear "light pipe" the LED shines through is also a button!) on the VRC0P until the LED flashes orange, then "Include Device" in the software tool bar, the "OK" in the pop-up box. When the VRC0P is included in the network, you will see the orange flashing light return to green flashing.
10. After everything is added to the network, don't forget to "associate" the locks to the serial interface (diagnostics -> RS232 Setup). Neither the locks nor the serial interface need to be in any special mode to do this, just leave them in their "normal" modes.
11. Hopefully your Z-wave network is now set up - but let's find out. With the VRC0P connected to your PC, again run Putty / Hyperterminal, 9600 baud, 8-N-1, same settings as above. Manually unlock and lock the lock. You should see serial data on the screen of the PC. If not, something is wrong already, either in the Z-wave network, software version or firmware versions. In my case, I now see:
After manual unlock:
<N003:152,064
<n003:000,113,005,021,001
After manual lock:
<N003:152,064
<n003:000,113,005,022,001
So I know my lock at Z-wave node 3 is working, I assume the 021 code tells the receiving equipment it's unlocked, the 022 code means locked.
12. If everything is working in step 11, you can send lock/unlock commands from the PC to the lock. In my case:
For remote unlock, type:
>N003SS98,1,0 -and press enter; you have to type the initial ">" character!
The lock "unlocks" itself and responds:
<E000
<N003:152,128,131,036,164,002,082,007,192
<X000
<N003:152,064
<n003:000,113,005,025,001
For remote lock:
>N003SS98,1,255 -and press enter; you have to type the initial ">" character!
The lock "locks" itself and responds:
<E000
<N003:152,128,102,046,199,033,234,182,056
<X000
<N003:152,064
<n003:000,113,005,024,001
If you got this far, you are doing great! You are ready to add the Z-wave network to the OP2.
13. In my case, I now moved the VRC0P to an outlet near my OP2 panel. I re-ran the tests above and my system failed! I moved the VRC0P to an outlet on my UPS, ran the tests again, and it worked. I moved it back and forth a few times to make sure what I was seeing was real, and it was. I'm not sure what is making AC power line noise on the outlets near my OP2, but my UPB PIM is right there (not on the UPS, and it looks like the OP2 power supply isn't on the UPS either, both of which I will be changing!), maybe it's the LED ceiling light. Either way, I'm leaving the VRC0P on the UPS - and it clearly needs clean AC power!
14. Program the OP2 panel to have a serial port set as "Z-Wave", add the locks under the "Access Control" portion of the PC Access software. You will need to know your node numbers from the Vizia RF+ software.
15. Connect the OP2 Z-wave serial port to your PC serial port. (Note: this is NOT the same cable as the VRC0P cable.) Use the same Putty / Hyperterminal settings as the Putty / Hyperterminal used above for the VRC0P (makes sense since the two boxes have to talk to each other!).
16. In PC Access, go to the Status/Control panel, and select "Access Control" at the bottom. You will see the locks you added in step 14. Double-click the lock, pick a command to send (lock/unlock) and send it. If everything is correct, you will see the serial data on your PC. In my case, I see:
For lock:
>N003SS98,1,255 - then a 5 second pause, then:
>AB - then a 30 second pause, then:
>N003SS98,1,255 - then a 5 second pause, then:
>AB - then a 30 second pause, then:
N003SS98,1,255 - then a 5 second pause, then:
>AB - then a 60 second pause, then:
N003SS98,2 - then a 5 second pause, then:
>AB - then a 30 second pause, then:
N003SS98,2 - then a 5 second pause, then:
>AB - then a 30 second pause, then:
N003SS98,2 - then a 5 second pause, then:
>AB
What I think: since these commands are going to a PC, the OP2 isn't getting the feedback from the lock; so it repeats the command 3 times. I believe the second set of commands is the OP2 looking for the status of the lock - but I could be totally wrong here! I think the ">AB" command is sent to the VRC0P to tell it to "abort" the previous command before sending another command.
17. At this point, you have a functioning Lock-PC system, and a functioning OP2-PC system. It makes sense to plug the two systems together and they should just work. The cable between the two systems is custom! A four pin RJ11 is used at each end, flip pins 1 and 4, pin 3 is straight through. For my pin numbering, hold the cable in your hand, connector facing away; connector plastic lock tab down, gold pins facing up at you. Pin 1 is on your left, pin 4 on the far right. The cable is reversible, it doesn't matter which end you plug into what.
##
Now, all this being said, I have intermittent operation between the lock and the OP2. Sometimes it works one way but the status doesn't change, sometimes the status changes when the lock is manually operated. In my case, the OP2 closet is directly under the mud room door lock. My guess is that I have 15 feet between the lock and the VRC0P. I know the VRC0P (running in that location) is good because of my direct-PC tests work every time. I've made 2 different cables, same intermittent OP2 results. Next I'm going to ohm out the cables to make sure they are good. I'm thinking I may need to use a shielded cable, like the RF from the VRC0P transmitting next to the wire is interfering with the RS232 data signal in the wire. Or maybe one of those ferrite torroid chokes to loop the interface wire around.
In my experience, I never cared for the Z-wave wireless locks. I give the lock a 100% on receiving commands from the OP2 and acting correctly. I give it 90% on sending lock position status back to the OP2. And it's that last 10% that will always get you - is it really locked or not?
Sorry this was so long, I hope it helps someone else.
Doug