linuxha,
I think you are just a tiny bit ahead of me on this stuff (if you haven't detected sarcasm, read it again with sarcasm in mind).
Have you figured out any other http commands? Perhaps something that returns the state of an output or input without gettinng all the other stuff that the gui sends back?
Also, you don't have any idea why I can't get my email working do you? I suppose it could be something with godaddy, but I don't know what other mail server to use for smtp port 25.
Thanks,
Lou
Sorry sometimes I get too serious and miss subtle hints (my wife now use very large subtle hints - 10lb hammer large subtle hints).
BTW, your ISP might block port 25 (I know Comcast does). We have to use alternate ports to access outside mail services.
I did have the information some where. I'm not sure where I put it. I should have my new work bench up within a week. I still need to run networking and cable up the terminal server. Then I'll be ready to start playing again (and I'll need that information).
BTW, Mark's URL is for WebControls without the PLC support. The firmware I have is with the PLC code.
Here's how you can put all the information into xml:
http://webcontrol.uu...621719880887507
or
/api/status.xml?rand=0.8621719880887507
It (status.xml) then looks like this:
<response>
<op1>0</op1>
<op2>0</op2>
<op3>0</op3>
<op4>0</op4>
<op5>0</op5>
<op6>0</op6>
<op7>0</op7>
<op8>0</op8>
<ophex>0x00</ophex>
<var1>0</var1>
<var2>0</var2>
<var3>0</var3>
<var4>0</var4>
<var5>0</var5>
<var6>0</var6>
<var7>0</var7>
<var8>0</var8>
<ip1>0</ip1>
<ip2>0</ip2>
<ip3>0</ip3>
<ip4>0</ip4>
<ip5>0</ip5>
<ip6>0</ip6>
<ip7>0</ip7>
<ip8>0</ip8>
<ts1>2.5 C</ts1>
<ts2>2.7 C</ts2>
<ts3>unbound</ts3>
<ts4>unbound</ts4>
<ts5>unbound</ts5>
<ts6>unbound</ts6>
<ts7>unbound</ts7>
<ts8>unbound</ts8>
<tstat1>ok</tstat1>
<tstat2>ok</tstat2>
<tstat3>unbound</tstat3>
<tstat4>unbound</tstat4>
<tstat5>unbound</tstat5>
<tstat6>unbound</tstat6>
<tstat7>unbound</tstat7>
<tstat8>unbound</tstat8>
<romcode1>102110420008</romcode1>
<romcode2>10B26B070000</romcode2>
<romcode3>000000000000</romcode3>
<romcode4>000000000000</romcode4>
<romcode5>000000000000</romcode5>
<romcode6>000000000000</romcode6>
<romcode7>000000000000</romcode7>
<romcode8>000000000000</romcode8>
<hs1>0 %</hs1>
<aip1>454</aip1>
<aip2>0</aip2>
<aip3>0</aip3>
<aip4>0</aip4>
<aip5></aip5>
<aip6></aip6>
<aip7></aip7>
<aip8></aip8>
<date>06/04/2011</date>
<time>18:37:53</time>
<datetime>06/04/2011 18:37:53</datetime>
<ipaddr>192.168.1.14</ipaddr>
<macaddr>00:22:12:01:02
C53</macaddr>
<name>WEBCONTROL </name>
</response>