IR control problem

[ajeysp]

Hi Everyone

I am using the iredtouch application off the itouch along with Global Cache's WF2IR controller. I am able to control a lot of devices, just by "learning" the IR codes, using the WF2IR module. However when I try this method to try controlling the Daikin split AC (model Daikin FT50GV1G6), the method doesn't work. When I try using the iLearn utility (provided by the Global Cache website), and learn the code, and test it, the code works. When I looked at the ir code that was recorded on the iredtouch application and that by the ilearn utility, they looked completely different.
To get this working, is there a way that I can "transfer" the correct code from the ilearn utility to the iredtouch application? Any help would be greatly appreciated.

Ajey

P.S. I am attaching the file that is generated by the iLearn utility that has the code that works correctly.

 

[ajeysp]

Hi Everyone

Further to my post above....

I am pasting below the code that I get on the iredtouch application when I record from the on/off button of the Daikin AC remote:

GC-iTach,37091,128,64,16,48,16,16CCBCCCCBCBBCBBBBBCCBCCCCCCBBBBCCCCCCCCCCCCCCCCCCCCCCCCCBCCCCCC,16,1099

In case it helps, I am also pasting the code that I see in the ilearn (which works when I test it from ilearn):

[AC]sendir,2:2,1,37091,1,1,128,64,16,48,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,48,16,16,16,48,16,48,16,16,16,48,16,48,16,48,16,48,16,48,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,48,16,48,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,1099,128,64,16,48,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,48,16,16,16,48,16,48,16,16,16,48,16,48,16,48,16,48,16,48,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,16,16,48,16,48,16,48,16,48,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,48,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,16,48,16,16,16,16,16,16,16,48,16,48,16,16,16,3709

When I save this code in ilearn (using the format "GC Compressed") I get the following corresponding code:

sendir,1:1,1,37091,1,1,128,64,16,48,16,16CCBCCCCBCBBCBBBBBCCBCCCCCCBBBBCCCCCCCCCCCCCCCCCCCCCCCCCBCCCCCC16,741

If you compare this with the code that we see in iredtouch, the initial part looks quite similar, but overall the code seems smaller. I did add the two "1"s after the code in iredtouch which seem to be missing before the "128", but it did not help.

I would really appreciate if you can offer any clues on this very critical issue.

Ajey