pete_c said:
Best way for us to help you is for you to post all of your stuff as relating to your implementation.
Create a little spreadsheet of your stuff and post it here. I am guessing you have documented everything so far.
Draw a loosey goosey picture of you home, sensors, doors, keypad positions and post it here.
Personally the more I know about what you know helps me understand your basic knowledge base of the panel and helps me write or offer the best advice.
Took a picture of it, but unable to reduce picture size easily at present, so will have to settle for word picture. I'm not very facile with picture drawing software, but the below should give you some idea.
Old 3 serial port OP2, after chip upgrade to FW 3.14a
Network enabled, static IP using dealer PCA current version network access
HAI UPB interface (not working, i think i misterminated the serial cable)
I added 1 16 zone hardwire expander and one 20a30-1 omni notifier, connected and programmed the RC 80s,
I believe there is one 39a00-1 powerline phase coupler, but I haven't found it yet. I have a spare.
14 door switches Honeywell 951WG zones 1 - 6, 14, 15, 17 - 22 configured as e/e zone type, 1k ohm resistors present, entry delay 30 and exit delay 60
3 Edwards signalling 2315A-L magnetic switches, zones 27 - 29 only 1 currently wired, x2 entry delay, 1k ohm present e/e zone x2 entry delay
7x System Sensor 4WT-B 4 wire photoelectric and thermal smokes zones 7 - 13, ESL 204 and 1k ohm present, zone type fire. ESL 505-03 uninstalled due to no internal sounder on the 4WT-B.
4x Visonic NEXT K9-85 motion detectors, 1k ohm present, I have already purchased Risco iWise dualtech 25 m motion detectors for 2 of the zones, and am considering replacing one or both of the remaining Visonics
2x Omnistat RC 80 thermostats for cooling only, zone 16 configured as following:
- Item 00 address – 1 (S) 2 (N)
- Item 01 communications mode 1
- Item 02 system options 20
- Item 03 display options 7
- Item 04 calibration offset 30
- Item 05 Cool setpoint limit 60
- Item 06 Heat setpoint limit 80
- Item 11 Cooling minimum on/off time 8
- Item 12 Heating minimum on/off time 8
- Item 14 clock adjust 30
- Item 15 Filter reminder 60
Radiant floor heating currently not interfacing with OP
1x non-speaker Omni keypad
1x OmniTouch keypad
1x interior sounder
1x exterior sounder? there is resistance across the circuit, but it makes no noise.
Many 35A00-1 UPB 600 watt dimmer switches, and auxiliary switches, currently configured as 12 rooms, Probably need to repeat the entire configuration process according to OP2 firmware 2.9 release starting page 19.
4 SA URD30 outlets
2 room controllers
1 house controller
SnapLink
Russound CAV 6.6 currently not interfacing with OP2, many installation issues although it is working.
There are some cryptically labelled wires in the panel, currently unused. Also on the to do list, there is another panel with video cable, some hardware, and coax hanging out of the home at various points, and a couple of new in box circa 2005 video cameras. My experience with video is minimal, so that's somewhere around the priority level of the Russound.
Also conspicuously missing is glass break and window sensors, I am considering a wireless protocol and hardware for this.
There was nothing written on the HAI can, of the above the only thing installed when I got there were 4 random doors and the smoke detectors. There was much evidence to suggest that whoever started installing the system quit in the middle of the job (why all the spare parts?).