Hi, newbie here and would appreciate your input. After many months of researching and reading posts from this and other websites I finally decided to purchase and install an Elk M1 Gold system. I’m halfway done with the installation of the Elk system but decided to pause and make sure I’m not missing anything. Below is a list of the items I've purchased to date:
I don’t have POTS, I’ve wired most devices but went wireless with a few hard to get door and window contacts and intend to expand the system in the future to add door locks and thermostat control.
Any feedback would be greatly appreciated.
Thanks!
- ELK M1 Control System
- ELK-M1GKS M1 Gold Control Kit without Enclosure
- M1 Gold Control Board
- ELK-M1KP2 LCD Keypad
- ELK-1280 8Ah Battery
- ELK-TRG1640 AC Transformer
- ELK-73 Echo Paintable Interior Speaker
- ELK-952 Surge Protector
- ELK-RJSET Telco Jack & Cord (not using)
- M1 Gold Control Board
- ELK-M1XEP Ethernet Interface
- ELK M1XIN 16 Zone Input Expander
- ELK P212S Supervised Remote Power Supply
- ELK TRG1640 AC Transformer 16.5VAC, 45 VA
- ELK-1280 8Ah Battery
- ELK P212S Supervised Remote Power Supply
- ELK-M1DBH M1 Data Bus Hub
- ELK-M1BBK2 recessed, “flush” mount
- ELK-M1KPNAV Navigator Touchscreen Keypad
- ELK-M1XRFTW Wireless Transceiver
- ELK-6010 Four Button Keyfob
- ELK-M1TWI M1 Gold Two Way Listen-In Interface
- ELK-SP12F Flush Mount Speaker
- ELK-M1TWSF M1 Two Way Flush Mount Speaker/Microphone
- ELK-SP12F Flush Mount Speaker
- ELK-SWB28 28” Structured Wiring Box
- ELK SWS Structured Wiring Battery Shelf
- ELK-M1GKS M1 Gold Control Kit without Enclosure
- Cellular Communication Center
- UPLINK 2500STD ANYNET GSM CELLULAR
- ELK-M1XSP Lighting/Thermostat Interface, Serial Port Expander
- ELK-P983 Power Supply for Cellular Alarm Transceiver
- ELK-1280 12V 8Ah Sealed Lead Acid Battery
- ELK TRG1640 AC Transformer 16.5VAC, 45 VA
- ELK 965 Low Battery Cutoff & Mst Power Switch
- ELK-M1XSP Lighting/Thermostat Interface, Serial Port Expander
- UPLINK 2500STD ANYNET GSM CELLULAR
- Wire
- 22/2-for 2 wire non-powered sensors (door and window contacts, etc)
- 22/4-for 4 wire sensors requiring power (motion/carbon monoxide detectors etc)
- 18/2-for 2 wire speakers
- 18/4 Firewire-for smoke/heat
- 18/4-for 4 wire speakers/mic
- Cat5e-for Keypad and camera
- 22/2-for 2 wire non-powered sensors (door and window contacts, etc)
- Devices
- Smoke Detectors
- 4WTA-B Photoelectric Smoke Detector with Thermal Sensor
- RRS-MOD System Sensor reversing relay/synchronization module
- SYSTEM SENSOR EOLR-1 SPST End of Line
- 4WTA-B Photoelectric Smoke Detector with Thermal Sensor
- Door/Window Contacts
- 3/8" Stubby Recessed Contact with Rare Earth Button Magnet
- ELK-6020 Slim Line Door & Window Sensor
- 3/8" Stubby Recessed Contact with Rare Earth Button Magnet
- Motion Detectors
- AURORA - ADEMCO PIR Motion Detector
- Carbon Monoxide Detectors
- 250-CO - Ge Security SafeAir Carbon Monoxide Detector
- Glass Break detectors
- 5822A-W - Recessed ShatterPro II Acoustic Glassbreak Sensor
- Smoke Detectors
I don’t have POTS, I’ve wired most devices but went wireless with a few hard to get door and window contacts and intend to expand the system in the future to add door locks and thermostat control.
Any feedback would be greatly appreciated.
Thanks!