Hello- I'm new to the Elk
My system so far:
1: Main board JP3 not terminated
2: 1ea. retro keypad hooked to the main board bus, JP2 terminated.
3: 1ea. M1DBHR Data Bus Hub hooked to the main boards bus, JP1,2,3,4 are terminated.
4: 1ea. M1XSP Lighting, Thermo and Serial Expander, hooked to branch 2 of the DBHR, JP2 terminated.
5: 1ea. M1XRF Wireless Receiver and Input Expander, hooked to branch 1 of the DBHR, address 2, JP1 terminated.
6: 1ea. M1XEP Ethernet interface, forced static IP, this is what RP is using to talk to the M1.
7. 5ea. GE 60-688-95 wireless micro sensors
8. 2ea. Sentrol 5885 Motion/ Glass Break
All data bus hub devices are enrolled and showing up in RP, Keypad T1 Addr=01, Zone Expandr T2 Addr=02, SerialPExpdr T5 Addr=01. I do get “KP1 Addr -> 1 Lost Comm” message displayed on the LCD during the enrolling process. I’ve tried changing the keypads address, but the message still happens just with the new address. I haven’t been able to figure this one out yet, jumpers?
I’ve been trying to activate my wireless sensors without any luck. The XRF originally showed up in RP as 16 hardwired zones. I deleted the hardwired expander then added a new wireless 16 zone expander starting at 17. I enabled the zone, entered the Tx ID, Normal supervision, pretty much followed the video. Now what?
My installation manual doesnt have the 2G after the M1XRF, I can’t find in on the PCB either. Do I have the right expander for these sensors?
Thanks- Rick
Update: The box the wireless receiver came in says M1XRF2G on it, GE 144 wireless GE crystal transmitters. The Box label says firmware Ver: 1.0.4..1.0.8.
My system so far:
1: Main board JP3 not terminated
2: 1ea. retro keypad hooked to the main board bus, JP2 terminated.
3: 1ea. M1DBHR Data Bus Hub hooked to the main boards bus, JP1,2,3,4 are terminated.
4: 1ea. M1XSP Lighting, Thermo and Serial Expander, hooked to branch 2 of the DBHR, JP2 terminated.
5: 1ea. M1XRF Wireless Receiver and Input Expander, hooked to branch 1 of the DBHR, address 2, JP1 terminated.
6: 1ea. M1XEP Ethernet interface, forced static IP, this is what RP is using to talk to the M1.
7. 5ea. GE 60-688-95 wireless micro sensors
8. 2ea. Sentrol 5885 Motion/ Glass Break
All data bus hub devices are enrolled and showing up in RP, Keypad T1 Addr=01, Zone Expandr T2 Addr=02, SerialPExpdr T5 Addr=01. I do get “KP1 Addr -> 1 Lost Comm” message displayed on the LCD during the enrolling process. I’ve tried changing the keypads address, but the message still happens just with the new address. I haven’t been able to figure this one out yet, jumpers?
I’ve been trying to activate my wireless sensors without any luck. The XRF originally showed up in RP as 16 hardwired zones. I deleted the hardwired expander then added a new wireless 16 zone expander starting at 17. I enabled the zone, entered the Tx ID, Normal supervision, pretty much followed the video. Now what?
My installation manual doesnt have the 2G after the M1XRF, I can’t find in on the PCB either. Do I have the right expander for these sensors?
Thanks- Rick
Update: The box the wireless receiver came in says M1XRF2G on it, GE 144 wireless GE crystal transmitters. The Box label says firmware Ver: 1.0.4..1.0.8.